PROJ-FILE-FMT=2              	; MANDATORY this must be the first line.   

; this driver does one thing - it sets the passive flag to TRUE
; all of the other values are unimportant

PROJ-NAME='Slave Panel Driver' ; MANDATORY single quoted text up to 32 bytes
PROJ-DRIVER-REV='Rev C'    		; MANDATORY number for pre-release, letter for release

IR-TIME-0L=1.315m					; MANDATORY special 0 or 1 on/off pairs
IR-TIME-0H=420u			 
IR-TIME-1L=315u
IR-TIME-1H=695u

PASSIVE-MODE = TRUE					; this is the key to this driver
									; the rest is truly ignored

PROJ-BAUD-RATE=9600,8,N,1 

VOL-MUTE=0
VOL-RANGE=205
VOL-FLOOR=50

RSCODE['DUMMY']		="",IS-SELECTION
RSCODE['POWER ON']	=""					
RSCODE['POWER OFF']	=""
RSCODE['VOLUME']	=""
RSCODE['POWER POLL']=""

; POWER Polling Section MANDATORY IF 

POWER-POLL-INTERVAL=1s				; FREQUENCY
POWER-POLL-TIMEOUT=6s				; TIME TO WAIT FOR RESPONSE - TIMEOUT = FAIL (>0)
POWER-POLL-THRESHOLD=5				; NUMBER OF FAILURE BEFORE ASSERING POWER FAIL
POWER-POLL-STARTBYTE=5				; BYTE TO TEST
POWER-POLL-MATCH-ANY=FALSE 			; 
POWER-POLL-MATCH-BYTES="'12',13"	; 16 MAX ALLOWED
POWER-POLL-DURING-WARMUP=FALSE
POWER-POLL-DURING-LOCKOUT=FALSE
;POWER-POLL-TESTBYTE-MASK=$01		; SET TO FF IF NOT USED

; MANDATORY 

WARM-UP-DELAY=30s 						; TIME TO TURN ON WARM UP LIGHT COSMETIC ONLY
POWER-ON-DELAY=25s 						; RESORTATION OF SELECTION
DEFAULT-LOCKOUT=68s						; 
IO-DOWNTIME=6u 							; 29MS PER BIT
IO-CANCEL-DOWNTIME-ON-RX=TRUE			; 
USE-MODULATION-WHEN-WIRED=FALSE 		;
INVERT-LINE-WHEN-WIRED=FALSE        	;
CARRIER-PERIOD=10u						; 
CARRIER-DUTY-CYCLE=50					; DEFAULTS TO 50%
PROJ-USES-ABSOLUTE-VOL=TRUE 
IR-WIRING-OPTIONS=IR-Emitter,Wired-Serial

POWER-SENSE-OPTIONS=RS232POLL,SENSOR
PROJ-MISSING-THRESHOLD=10          		; NUMBER OF TIMEOUTS - ONLY USED WHEN PROJ IS POLLING AND TELLS 1 - 255

; FIRMWARE FOIBLES
BYTES-TO-QUEUE=2                        ; 

; Section for setting the defaults of the hidden functions

DEFAULT-HID-FUNCT[OFF]		=''					; OPTIONAL
DEFAULT-HID-FUNCT[VUP]		=''					; OPTIONAL
DEFAULT-HID-FUNCT[VDN]		=''					; OPTIONAL
DEFAULT-HID-FUNCT[1]		=''					; OPTIONAL
DEFAULT-HID-FUNCT[2]		=''					; OPTIONAL
DEFAULT-HID-FUNCT[3]		=''					; OPTIONAL
DEFAULT-HID-FUNCT[4]		=''					; OPTIONAL

; MANDATORY Section for setting the defaults of the CORE functions

DEFAULT-CORE-FUNCT[ON]		='POWER ON'               	; MANDATORY
DEFAULT-CORE-FUNCT[OFF]		='POWER OFF'               	; MANDATORY
DEFAULT-CORE-FUNCT[POLL]	='POWER POLL'              	; MANDATORY
DEFAULT-CORE-FUNCT[VUP]		='VOLUME'              		; MANDATORY
DEFAULT-CORE-FUNCT[VDN]		='VOLUME'              		; MANDATORY
;DEFAULT-CORE-FUNCT[REPEAT]	=''							; OPTIONAL
;DEFAULT-CORE-FUNCT[PREFIX]	=''							; OPTIONAL
;DEFAULT-CORE-FUNCT[SUFFIX]	=''							; OPTIONAL

; MANDATORY Section for setting the defaults of the selections

DEFAULT-SELECTION[1]		='DUMMY'					; MANDATORY
DEFAULT-SELECTION[2]		='DUMMY'				 	; MANDATORY
DEFAULT-SELECTION[3]		='DUMMY'					; MANDATORY
DEFAULT-SELECTION[4]		='DUMMY'					; MANDATORY

DOC-INSTALLATION-NOTE[1]="This is a special driver that will place the panel in SLAVE mode.  This is useful if you are using two panels to control one projector, or if you are using a third party control system.  Please see the Appnote for more information on how to connect the Panel."   ; there can be several of these
REQUIRES-FW-VERSION=$01,$01